Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Just about every person has got their personal assumption in relation to Installing A Bathtub.
Installing a bath tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and often, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old bathtub is conveniently obtainable, the task can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub and also set in the new one. Make sure you have actually qualified yourself for the work and also fit trying it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to consider using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you mount a brand-new bath tub in your shower room if you have already purchased a new bathtub as well as do not need to change the setup of your previous water system pipes.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the limited access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making sure that the washers are in place between the faucet as well as the sink. Protect the tap in position with the maker given backnut. As soon as the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wooden boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub until the level reads level.
To install taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other tap.
Switch on the water system as well as check all joints and brand-new pipework for leaks as well as tighten them if essential. Load the tub as well as additionally check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bath tub must wait until the bathtub has actually been used at the very least when as this will settle it into its last placement.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, creating the water to pass through the wall surface between the bathroom and also the tiling, bring about issues with dampness and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealant can crack relatively early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog entry on A Step-by-Step Guide to Installing a Bathtub when browsing the internet. Be sure to set aside a second to promote this entry if you enjoyed reading it. Thank you so much for going through it.
Best in business. Report this page